chipped ecus question!!

[cuzzfolk99]

I know this may be a noob question but im kind of confused when i get an chipped ecu from phearable .net i choose what program i want it to be chipped with right? ok then i go to a tuner and they tune it on that program?? im turboing my 00 si and i need to know this asap and i know that i have to also get the obd2b to obd1conversion harness but someone please help me out quik thanks

 

[io_303]

the chip that comes from phearable will have a basic basemap that you can drive around on, but before you do any major pulls you will need to get it dyno tuned.

 

[cuzzfolk99]

ok and i can choose the program that i want to get it chipped with right?

 

[jimmyb34]

youll need to go to obd1 yes... id find out whatever your tuner uses and go with that.. some tuners wont mess with uber or crome, some will

 

[io_303]

ok and i can choose the program that i want to get it chipped with right?

Xenocron asks for your setup and builds a basemap off of that, I am almost positive that phearable does the same

 

[cuzzfolk99]

ok thanks alot

 

[Shiznit]

youll want to check with the tuner to see if they tune the program that you want to put on your ecu.

 

[cuzzfolk99]

do any of you guyz know of any good tuners in the SC NC area??

 

[io_303]

I dont know how out of date these are, but these are from the pgmfi tuner directory

Crome
20. Name: Kevin Thackston
Location: Jacksonville, NC (east coast NC)
Contact: 00projekteg@netscape.com, email or pm for phone number
Tools: Moates Ostrich, PLX wideband, IBM thinkpad, Willem burner, dyno access (with appointment), ecu with knock board to monitor ks, data logging, chipped ecu's and supplies, etc.

22. Howard (airshifter) 11.11@122 allmotor street EG hatch

Speed Innovations
313 Manor Ave Sw
Concord, NC 28025
704-262-7948
speedinnovations@ctc.net

Uberdata:
Import Jedi
Name: Larry Stevenson/rpm automotive and performance
Location: Jacksonville, NC
Phone: 910-577-5200 shop,910 382 5006 cell
Email: fast1stgen@hotmail.com
AIM: import jedi
MSN: import jedi
Yahoo: mportjedi
Equipment: LM-1 wb, xtronics burner and romulator, nokia data cable, dell laptop

Joseph Davis
City, State: ashEVILle, NC
Email/Other Contacts: george1879@charter.net
Phone #: use email pls kthx!
Equipment: Pair of Techedge 2A0 rev 3 widebands, a 2C0, Thinkpad T20, Batronix 3.2 burner, EconoROM III romulator, Ostrich, DIY KS audio monitor, RoadDyno (accurate dyno sheets, limited in power to traction on the street), can arrainge dyno time by appointment.

projekteg
name/company: kevin thackston/projekTuning
location: jacksonville, nc
email: 00projekteg@netscape.com
phone: pm for phone number
equipment: think pad lappy, plx m300 wide band, serial data logging, ostrich, willem burner, dyno available, chipping supplies in stock/spare ecu's

 

[io_303]

Guess i should post the link too

http://forum.pgmfi.org/viewforum.php?f=29&start=0&sid=c9e49b381b3a72af51fbb4026909b4e8

You will need to create an ID to read the link

 

[vandynamics]

if they specify between uberdata and crome is most likely because of the datalogging process.

if your using crome and plan on datalogging you have to clip j12 to remove the full duplex mode. where as uberdata will run either 1/2 or 1 duplex.

other than that, they chip socket, chip used, and process is all the same.