DB7 exhaust on my 98 Civic LX

[endo617]

Just got a 98 Civic LX, that I will be putting my B18c1 from my old DB7 but wondering if the exhaust will fit from my integra to my civic. Looked but never got a definite answer just maybes.

 

[CO671]

From this thread:
http://honda-tech.com/showthread.php?t=2760065

an integra SEDAN rear section should bolt up just fine. EG 2/4 door and DC Sedans have interchangeable exhausts (I have an ITR sedan exhaust on my coupe).


I would assume yes, since (i'm not too sure on these facts) 92-00 Civic sedans/coupes exhausts can bolt up to each other based on the undercarriage shaping and 92-00 Civic hatchbacks can fit each other.

 

[endo617]

From this thread:
http://honda-tech.com/showthread.php?t=2760065

an integra SEDAN rear section should bolt up just fine. EG 2/4 door and DC Sedans have interchangeable exhausts (I have an ITR sedan exhaust on my coupe).


I would assume yes, since (i'm not too sure on these facts) 92-00 Civic sedans/coupes exhausts can bolt up to each other based on the undercarriage shaping and 92-00 Civic hatchbacks can fit each other.

Thanks, but I forgot to mention like an idiot. I want to us the complete exhaust header back

 

[CO671]

Oh, i didn't notice that quote said "rear section"

I know you meant complete exhaust system (header to axle back)
I can't find much but here is something:
http://honda-tech.com/showthread.php?t=2411791
I have a DC2 ITR exhaust (cat back) on my EK sedan. I had to lenghten the tail pipe on the muffler by 5" to leave it sitting flush with the rear bumper...but all bends and hangers are in the same locations on both cars. I was told that a DB8 Integra exhaust is the same lenght as an EK sedan, and sedan and coupe exhausts are the same lenght so it figures that you should be able to swap the exhaust straight over to the integra sedan without having to change anything at all.

 

[endo617]

Oh, i didn't notice that quote said "rear section"

I know you meant complete exhaust system (header to axle back)
I can't find much but here is something:
http://honda-tech.com/showthread.php?t=2411791
I have a DC2 ITR exhaust (cat back) on my EK sedan. I had to lenghten the tail pipe on the muffler by 5" to leave it sitting flush with the rear bumper...but all bends and hangers are in the same locations on both cars. I was told that a DB8 Integra exhaust is the same lenght as an EK sedan, and sedan and coupe exhausts are the same lenght so it figures that you should be able to swap the exhaust straight over to the integra sedan without having to change anything at all.

Appreciate the quick replies man. Thank you, took some stress off me. DB7 wiring burned so stressed out right that I have to rush into getting something on the road. Build thread coming soon.

 

[endo617]

Oh, i didn't notice that quote said "rear section"

I know you meant complete exhaust system (header to axle back)
I can't find much but here is something:
http://honda-tech.com/showthread.php?t=2411791
I have a DC2 ITR exhaust (cat back) on my EK sedan. I had to lenghten the tail pipe on the muffler by 5" to leave it sitting flush with the rear bumper...but all bends and hangers are in the same locations on both cars. I was told that a DB8 Integra exhaust is the same lenght as an EK sedan, and sedan and coupe exhausts are the same lenght so it figures that you should be able to swap the exhaust straight over to the integra sedan without having to change anything at all.

Appreciate the quick replies man. Thank you, took some stress off me. DB7 wiring burned so stressed out right that I have to rush into getting something on the road. Build thread coming soon.

 

[CO671]

Good luck! lemme know if it fully bolts on or not, i'd like to know how that goes. Shoot.

 

[endo617]

Good luck! lemme know if it fully bolts on or not, i'd like to know how that goes. Shoot.

Sure will, i'll be the hamster to prove it lol

 

[endo617]

The Exhaust fits perfect, all hangers match up and clear, hope this helps someone else.