new member... couple of webcam pics (bad res. sorry)

[rcoolb2002]

Just a couple of pics of my stuff... sorry for the bad resolution. I took the pics with my webcam on my laptop haha.

Engine: b16a SiR2. .015" mill, "race" 3 angle, p&p, type-R oil pump, pr3 pistons, pr3 cams, completely rebuilt with honda gaskets, hastings rings, honda bearings. unorthodox lightweights.

Car: Tein springs, skunk2 camber kit, Si rims, naked interior, megans lca's, skunks stb, falken azenis.

 

[tonyM]

welcome to the site yo!
lets see some full pics of yer ride!
also,is that motor dropped yet?
letss see pics of that too!

 

[rcoolb2002]

welcome to the site yo!
lets see some full pics of yer ride!
also,is that motor dropped yet?
letss see pics of that too!

dont have any full pics, the digital was stolen. The motor is still sitting on the motor stand, and wont be in the hatch for a little while. Im putting it in a DA integra until its broken in and i know its reliable. Since i built it myself i cant risk losing my reliable daily. I really need to find a nice cheap camera haha, cause money seems to dissappear into my cars.

 

[JL]

I assume you mean 2nd gen B16 seeing as SiR2 is just a trim level like EX, DX, Si and does not reffer to different motors but why would you rebuild with PR3 (1st gen) cams and pistons therefore de-tuning the motor?

 

[FhCRubarb]

Whered u get the swap and for how much>?

 

[J32a2OwnsU]

Welcome!!! Nice ride. post some pix when shes done!!!

 

[rcoolb2002]

I assume you mean 2nd gen B16 seeing as SiR2 is just a trim level like EX, DX, Si and does not reffer to different motors but why would you rebuild with PR3 (1st gen) cams and pistons therefore de-tuning the motor?

Pistons and cams are stamped pr3. SiR is a trim level which came with a b16a. SiR2 is slang for second gen SiR. PR3 is the common b16a stamping. Maybe your thinking about ecu's. The PR3 is primarily a obd0 ecu, but came in the XSi as obd1 also.

 

[rcoolb2002]

Whered u get the swap and for how much>?

Got the motor as a lean longblock. Been building from there. Wasnt a "swap". In totaly ive probably got around 1500 in the longblock.

 

[42Steps]

That will be a nice little ride... Hope it all turns out ok.... Keep us posted....

 

[Andrey]

welcome to CC! Nice ride! I hope u'll stick to this site!

 

[Mr. Lin]

good choice of rims

 

[JL]

Pistons and cams are stamped pr3. SiR is a trim level which came with a b16a. SiR2 is slang for second gen SiR. PR3 is the common b16a stamping. Maybe your thinking about ecu's. The PR3 is primarily a obd0 ecu, but came in the XSi as obd1 also.

SiR2 was an actual trim level there was an Sir and 2 trim level offered in the 5th gen civic and both came with the same motor. PR3 was stamped on all 1st gen B16 parts. 2nd gen parts were stamped P30 like the ECU. P30 pistons are 2nd gen, not PR3............

PR3 pistons = 10:2:1 CR
P30 pistons = 10:4:1 CR

 

[CBR_3:16]

how much HP you plan to get?

 

[Genuine Rolla]

cant wait to see more pics dude!!!!

 

[Mr. Lin]

it's sad that your webcam is much better than some people's digital cams on this site...

 

[SilverSivic]

Looks good cant wait to see the motor dropped in keep us posted