watch these videos, car won't start

[6thgenex]

i posted it on my first thread
first time DIY head gasket replacement
well i need some feedback asap...
below are some videos i took last night after putting the finishing touchs to my car
filled her up with oil and coolant, etc, etc,
but now it won't start.
what's this sound like?
http://www.youtube.com/watch?v=raI2ZXGu4Hc
http://www.youtube.com/watch?v=eXkzhHN2q4A
let me know, thanks in advance

 

[SwiftEKtuner]

any cel codes?

 

[6thgenex]

oh and the check engine light is also on,
dumb question but how do i find out what the cel codes?

 

[UCCRacing]

Do you know anyone that has an OBDII Reader? IF so do that... If not then see if your local parts store has a rental???

Are you sure your timing is correct?

 

[RonJ]

1) Double check the mechanical timing. Post some pictures.
2) Does the fuel pump prime?
3) Is there spark at the plugs?
4) Pull the CEL codes.

See relevant links in my signature.

 

[6thgenex]

one of the tensioner pulleys has a mark to leave it sitting at 1 o'clock
and camshaft sprocket has the arrow point up...maybe not
there any writes up on setting the timing?

 

[6thgenex]

1) Double check the mechanical timing. Post some pictures.
2) Does the fuel pump prime?
3) Is there spark at the plugs?
4) Pull the CEL codes.

See relevant links in my signature.

the fuel pump primes, ill have to check for spark-think there is, and i need to pull the CEL codes

 

[RonJ]

This is how the mechanical timing (cam and crank synchronized at TDC1) should look:

 

[6thgenex]

thanks

 

[6thgenex]

http://www.youtube.com/watch?v=RKLa-PI01IM

got it to start, but now i hear a whistling/rattling noise now
what could it be?

 

[AllTracCelica]

Damn sure doesnt sound good.... Did you have the timing way off when you where cranking it before? Maybe dinged some valves if had it way off.

 

[6thgenex]

no, the timing was fine. wasnt off before i changed it.
i put the crankshaft pulley at TDC with the arrow facing up,
im thinking....
damn.

 

[AllTracCelica]

What did you do to car before all of this? Replaced head gasket? timing belt or what not? Why did it not start from beginning?

 

[6thgenex]

http://www.clubcivic.com/board/showthread.php?t=182216
posted on my first thread,
head gasket replacement, timing belt, a/c belt, p/s belt, alt belt, water pump
sounds like its coming from the water pump area...

 

[6thgenex]

What did you do to car before all of this? Replaced head gasket? timing belt or what not? Why did it not start from beginning?

the distributor was off and the spark plug wires werent on right,
sounds stupid i know but my friend put the wires on...should have double checked.

 

[got traction]

sounds like somthing wrong with bearing either on waterpump or timing belt tentioner (sp?) The first videos sounded like the motor was flooded...but i guess you got that cleared up now. Also sounds like its needs a valve adjustment

 

[6thgenex]

thinks its drivable?

 

[AllTracCelica]

eeeekks.... should check work no matter what check twice do once or big problems Are you sure timing belt is tightened to specs? Are you sure that you had all the area clean around water pump area no bolts fell in?

 

[AllTracCelica]

I would not drive it if valves are out of adjustment to far Learned my lesson the hard way getting head rebuilt because of it. Just a questions traction when im accelerating around 2.5k-4.5k i get a whining if i am sitting still i dont get it? Could this be the water pump cause i dont think it has ever been replaced......

 

[6thgenex]

positive that no bolts fell in, im going to have to double check to see if its adjusted to specs