thanks bro im really glad too. i have class tonight from 6:00 until about 7:40 but after that, providing Rob keeps his shop open so me and Yusif can use the lifts, we'll be finishing tonight. Keep your fingers crossed!
It's finally happening!
- Thread starter EM1_ProJect
- Start date
$lick Rick
TEOTWAWKI
Registered VIP
Registered OG
5+ Year Member
10+ Year Member
15+ Year Member
20+ Year Member
your headlights look fugged up, you should by the set i have sitting in my closet 
headlights are just covered in grease and oil from the install, they will be cleaned.
the piping, its just shavings from the block, they rusted over night. we started to use a wire loom to polish it off and then i was like..."nahhhh lets just put it on, f**k it i like the looks lol"
the piping, its just shavings from the block, they rusted over night. we started to use a wire loom to polish it off and then i was like..."nahhhh lets just put it on, f**k it i like the looks lol"
shane what happen to u bro? u block me on aim again?
lol i wouldnt have said that publicly...that made you look so weak lol. nah i got a new screen name, you got it nowcivicracing98 said:
More Pictures!
p.s. guys....no garrett, we threw on an ebay XSPOWER t3/74, and smaller intercooler so i could keep my fogs.
we also used a Revhard thermal coated log manifold. the BMC race was sold, this one is better anyways cuz it's revhard, and thermal lol
Btw...this car hauls f**kin ass. B18 ls non vtec on 10lbs.... ebay t3/t4 turbo same setup as me, mien is a little better
p.s. guys....no garrett, we threw on an ebay XSPOWER t3/74, and smaller intercooler so i could keep my fogs.
we also used a Revhard thermal coated log manifold. the BMC race was sold, this one is better anyways cuz it's revhard, and thermal lol
Btw...this car hauls f**kin ass. B18 ls non vtec on 10lbs.... ebay t3/t4 turbo same setup as me, mien is a little better
so have you driven it yet?? i want a full description lol since i'm taking the same route you are, eventually, and also, whats your clutch setup? sorry for all the questions but how much did the install run you? thanks 8)
ok here is it all in a nutshell. it's not tuned, except a base map, so i cant rev past 5K which is when my turbo his boost, so basically i have no boost until i tune it (hopefully tomorrow Nate is free).Going-West said:
for the kit...from experience of others, go with ebay for most s**t to keep it cheap.
ebay turbo
johnnyracecar.com intercooler
i got tunertoys injectors, but i'd go rc 450-550's low impedence
tunertoys.com IC piping $100 for ALL you need if you do it right
reliable wastegate
turbo xs rfl blow off valve (ebay special)
i spent $1600 in parts and about $700 in labor, which includes the BEST tune you can get around here. My boy Nate tunes everybody s**t to the best, better than any performance shop. f**k hondata, uberdata, aem..ECU baby! total came to $2300 installe and tuned
ok i had like an 8 inch greddy in height, and it took up my WHOLE grill, you couldnt even see the inlet/outlet in the grille, but then there was NO room for fogs at ALL. which is why i traded for a 6 inch height, smaller length FMIC and it was still a b***h to bend around the fogs and make it work. i had to cut half of my foglight brackets off to make the piping fit by it, on both sides. the bumper barely holds on the car lol. the screws are screamingLatinEM1 said:
the foglight cutting? i dont think i can fit my camera under my car....LatinEM1 said:
damn lookin good shane... can't wait to see the final product and the video 
I called the exhaust place today to see how much it would be to cut a hole in my downpipe for my o2 bong to be welded on for tuning and they said about $30 if i bring the downpipe in myself. If they have to put it on a lift then it is probably like $50 or something. I can't get it tuned until i get that o2 bong welded on there so.... depends what i buy my dad for his birthday, then we'll see how much i have left over.
Btw...on the blow off valve, does anybody know how many shims to put in?
The BOV comes with 5 but feedback says you use diff. amounts.
Btw...on the blow off valve, does anybody know how many shims to put in?
The BOV comes with 5 but feedback says you use diff. amounts.
axles? lol...of course stock axles. im running my stock clutch too right now until it breaks in like a week. i have to start saving for another one!LatinEM1 said: