CHILD'S *EK* ... finally i have an EK

[K-N-2-EK]

K-tuned RSX billet shifter and running my race spec shifter cables through the heater core outlet at the firewall. Still a bolt in affair, no worries about seized shifter cables due to exhaust heat, more space to tuck the exhaust closer to the body for more ground clearance, and more bling

Also, the K-tuned race spec cables fit a little awkward in the hybrid-racing box.

Neat idea I must say!
#twins

 

[Intertwined]

new plan sounds good. I especially like the thought of being able to tuck the exhaust up closer to the body.

 

[mymmeryloss]

I wish that shifter would work on my rx7 trans...

 

[OneFastGSR]

I like how you have a Works Bell hub and quick release, I remember this post on clubintegra about the differences in NRG and Work Bell and Work Bell is the only way to go. That's what i'll be getting if I get a aftermarket wheel. I like my JDM EG wheel atm though!

CI Thread on WB vs NRG http://www.clubintegra.com/board/showthread.php?t=78259

 

[CHILD]

I like how you have a Works Bell hub and quick release, I remember this post on clubintegra about the differences in NRG and Work Bell and Work Bell is the only way to go. That's what i'll be getting if I get a aftermarket wheel. I like my JDM EG wheel atm though!

CI Thread on WB vs NRG http://www.clubintegra.com/board/showthread.php?t=78259

I tend to use good parts.

 

[OneFastGSR]

That's why I like your build! I love it when people get the best stuff that you can get, I'd rather see a car with a few really nice parts than a bunch of cheaper parts. Quality over Quantity!

 

[CHILD]

I have a potential buyer for my Hybrid Racing shifter, so if that goes through I'll be picking up all my Ktuned alternatives in a day or so.

Also, hybrid-racing hit me up saying they have an AC/PS delete ready for me too

 

[young_]

3,988 posts later.. And I'm just ready for this thing to be done.

 

[CHILD]

3,988 posts later.. And I'm just ready for this thing to be done.

The moment that it's in, the whole thread will just continue with, "so what's next? When will you have that installed? Then what's next?"

I'm basically maxed out on upgradeable parts anyway. Got the best available from the kswap companies

 

[ReedMann]

Haha so true ^^^

 

[K-N-2-EK]

*cough ITB's cough*

 

[CHILD]

*cough ITB's cough*

Hahaha. Shut up before I waste more money lol. Been debating those and an allin fab manifold for later on. We'll see though

 

[OneFastGSR]

Them kinsler ITB's!!! 382 WHP all motor right here. Rob Reinen's EK

 

[CHILD]

The internal setup for his build is much more important than his itb's. My plan for ITB'S is on a much smaller scale.

 

[OneFastGSR]

Yeah lol. I understand that 100%! Rob's setup has tons and tons of stuff done to it. He's actually the one that sold me my civic hatch.

 

[K-N-2-EK]

Hahaha. Shut up before I waste more money lol. Been debating those and an allin fab manifold for later on. We'll see though

No pressure! Just get this swap done and enjoy the swap!

 

[CHILD]

Ran inside my bank and pulled out the semi autos and told the teller to put the money in the muthafckn bag, I have parts to buy!

When I got out of jail, I just placed an order using PayPal

Ktuned billet rsx shifter
Ktuned billet shifter base
Ktuned billet bushings
Ktuned bbillet shifter cable grommet

....poor again.

 

[K-N-2-EK]

Ran inside my bank and pulled out the semi autos and told the teller to put the money in the muthafckn bag, I have parts to buy!

When I got out of jail, I just placed an order using PayPal

Ktuned billet rsx shifter
Ktuned billet shifter base
Ktuned billet bushings
Ktuned bbillet shifter cable grommet

....poor again.

And I shouted... IM RICH B*TCH!

 

[buzzbombtom]

bushings made of aluminum?

 

[K-N-2-EK]

bushings made of aluminum?

Solid crisp shifting...there is no room for error with the k series tranny!