93 Sol Si d16z6 turbo build w/ Lots of Pics

[JDM B20 EG6]

93 Sol Si d16z6 turbo build

I have picked me up a 93 Del Sol Si with a z6 in it. Started out as a car for the wife. She got tired of it and I inherited it.

I let it alone for a while other than what it had on it when we got it. It had DC Sports 4-2-1 header and a unknown short ram and muffler.

Well after a few and havin the parts layin around from upgrades on my turbo Talon I decided to turbo it.

It was puttin down 235whp at 10psi. On stock motor. Well I had a boost spike and didnt have enough fuel for it and burnt a valve.

That lead to a complete rebuild/build up.

Here are the parts I have ordered/have to order:
JE/SRP 9.0:1 Pistons w/ JE rings 75mm
Eagle H beam rods
Stock Crank
ACL Race bearings
Air Research t3 60 trim
Edelbrock cast turbo mani
Custom 2.5" turbo back
Cometic 5 layer HG
DSM 510cc inj
Honda resistor box
Wally 190 lph (had brand new one layin around)
FMIC
Greddy BOV
HKS EVC-S Electronic boost controller
Chipped p28 tuned with Crome
Innovate LC-1 w/ XD-16
Xenocron 3 Bar DIY map
2.5" IC pipe
ARP Head studs
JGE Flat faced Black nitride SS valves
60mm B20 tb
Ported z6 mani
B&M AFPR
EG lip
M3 lip spoiler
GC coil-overs
GSR rear sway

I am building this motor in my computer room since the shop isnt built yet and the carport isnt closed in.

Here is a link to my album on photobucket. http://s18.photobucket.com/albums/b105/worpedteg/Delsol/

 

[JDM B20 EG6]

Here is what I started with:

Did this to it.

Long story short found this one day:

So I ripped into it and found this:

So I decided since I was doing a rebuild I would to a build up while I was at it. So I orders thees.

Then started clean up:

Here Is what I got after clean up:

So I started re assembly:

Then I found out I had to notch my griddle:

Here is the bottom end all finished:

 

[kingjmack]

Looking good so far!! I love the single cam build threads. Good Luck!

 

[JDM B20 EG6]

Thanks I got my ARP's installed today. Just waiting on valves now.

 

[civhatch92]

Not bad, looking forward to seeing this get built. Good luck man!

 

[DaOne]

Nice work so far!

 

[JDM B20 EG6]

Thanks everyone. I will update as I go. I am going to order a FMIC I already found. Waiting on turbo to get here and valves so I can finish the motor.

Does anyone have a pdf manual or a paper one they can scan for the HKS EVC-S? I bought a used setup and need a manual for it.

 

[JDM B20 EG6]

I shouldn't run lean again. I fixed my Innovate wide band tonight.

 

[somejaykid]

nice build up op keep us updated on it

 

[JDM B20 EG6]

Here is the block with the ARP's installed:

Here are a few of the z6 intake after being ported and polished to 60mm on tb side:

Here is the 60mm tb mounted:

Here is the HKS EVC-S working:

 

[civhatch92]

HKS EVC manual:
http://www.scribd.com/doc/22538022/HKS-EVC-6-Manual

 

[JDM B20 EG6]

The EVC 6 is different than the EVC-s Thanks though.

On HKS's website they have manuals for most all of their boost controllers and other electronics but dont have this one listed.

 

[Cooper76]

Looking good. I don't think I could get away with cleaning my block in the kitchen sink like that! I have a hard enough time when I spill oil doing an oil change. I never hear the end of it till it's all cleaned up.

 

[Robin...]

Looks like its going to be an awesome build...

 

[JDM B20 EG6]

The wife was more upset I used all her oven cleaner than cleanin it in the kitchen sink. Hell I'm building the motor in the computer room.

 

[JDM B20 EG6]

Intake mani most of the way together. B20 tb, DSM 510cc inj, waitin on Xenocron 3 bar map & B&M AFPR to get here.

 

[emerican]

Looks like its a great build man. I agree if i ever tried to even bring dirty car parts in the house that would be my ass would never even think of the kitchen sink. Subscribbed cant wait to see it done.

 

[cw3263]

super sick buiid bro, def in to see how this goes
subsrcibed

 

[JDM B20 EG6]

Thanks guys. I just need a set of valves to get the motor its self done. Everything else is already here.

 

[SleepingSol]

looks like a great build man.

just curious, why JE?